| |
|
This
adjustable blade semi-con scoring tool has a scoring depth from
1 to 90 mils (.025 to 2.286 mm) and is designed for “strippable” semi-con
URD cable shield. Its spring-loaded blade assembly assures consistent
scoring depth. It allows one handed scoring of circumference and
length.
|
|
| |
|
|
| |
|
This
tool is designed for .650 to 1.872 inch (16.51 to 47.63 mm) cable
O.D. and chamfers 15 to 35 KV cable. It creates a 45° bevel
approximately .125 inches long. It works for XLPE, Okonite and 3728
EP insulations and is perfect for pre-molded splices and terminations. |
|
| |
|
|
| |
|
|
| |
|
|
| |
|
| • |
For 15 to 34.5 KV elbow - small interface
|
| • |
For quick and easy insertion of the probe
inside the elbow |
| • |
Prevents load break probe contamination |
| • |
Prevents load break probe breakage |
| • |
Reduces cross threading |
| • |
Provides the proper tightening forces as
recommended by the elbow manufacturers |
| • |
Multiple torque delivery system:
– Delivers 125 inch-pound torque
– Adjustable (Full "T" Handle or
Moment arm for tight locations)
and removable "T" handle
– 7/8" (22mm) steel drive and wrench or Channel Locks
– 3/8" (10mm) square drive socket |
| • |
Load Break Probe quickly removed by simply reversing the
tightening action |
| • |
Available for all load break elbows • U.S. Patent No.:
5,605,082 |
| • |
Length: 9.375 in (238.13mm) • Weight: 1 lb 4 oz (568
g) |
|
|
| |
|
|
| |
|
| • |
For 600 amp Separable Connector Systems |
| • |
Provides quick, easy installation of:
- Connector Plugs
- Reducing Tap Plugs
- Reducing Tap Wells |
| • |
Prevents over-tightening which could lead to premature failures |
| • |
Prevents over-tightening leading to loose connections |
| • |
Eliminates the need for an external torque wrench |
| • |
Eliminates the need for wrench length calculations |
| • |
Long spanner prong prevents wrench slippage |
| • |
Supplies the proper torque (50 - 60 ft-lb) as recommended
by the
manufacturers |
| • |
Length: 14 3/8” (36.5 cm) |
| • |
Weight: 2 lb 3 oz (1 Kg) |
|
|
| |
|
|
| |
|
| • |
Allows proper installation of Landis & Gyr "K" Base
3 Phase or similar meters without shorting, sparking or flashover |
| • |
Tool is insulated and isolated from meter base with composite
shaft which is rated to 1000V |
| • |
Prevents over and under tightening with 150 in-lb preset
torque setting accurate to ± 15 in-lb |
| • |
1/2" (12.7 mm) square socket drive accepts magnetic
installation socket |
| • |
Adjustable “T” handle |
| • |
WARNING: Do not use this tool for removal of un-torqued terminals
or serious shaft damage may occur. |
| • |
3/8" (9.5 mm) square socket torque test point |
| • |
Length: 13 3/4" (349.25 mm) • Weight: 19 oz (539.13
g) |
|
|
| |
|
|
| |
|
This
tool is designed for stripping the outer jackets or insulating material
on cables ranging in size form ½” up to 2 ½” (12.7
to 63.5mm) O.D. The “Dual Position” jaw makes the tool
extremely versatile for electric utility applications.
|
|
| |
|
|
| |
|
| • |
For 1/0 AWG to 1000 MCM URD cable |
| • |
.500 to 2.25 in (12.70 to 57.15mm) cable O.D. |
| • |
Two handles permit safe, easy operation on XLPE, plastic,
polyethylene and EPR insulation of all thicknesses |
| • |
Adjustable strip stop bar gives an exact stripped conductor
length and can be rotated to allow unlimited stripping |
| • |
Safe, clean cuts prevent conductor damage |
| • |
CB 50 blade included with tool |
| • |
Adjustable to fit wide range of cable O.D.'s |
| • |
Replacement blades:
CB 50A – Standard Reach blade
CB 50 – Long Reach blade |
| • |
Length: 14.5 in (368mm) |
| • |
Weight: 2.1 lb (953 g) |
|
|
| |
|
|
| |
|
Designed
for 600 volt secondary cable. Cutting heads available for #6 to 500
MCM conductors (concentric, compressed or compacted).
Strips 45 MIL to 110 MIL XLPE, polyethylene and EPR insulation. Offers
choice of square cut or chamfer cut blades. This tool enables you
to strip the cable quickly, even in cold climates.
|
|
| |
|
|
| |
|
Length: 10.88 in (279.00 mm)
Weight: 2.47 lbs. (1.13 kg)
| • |
For .320 to .790 in (8.13 to 20.07mm) Cable O.D. |
| • |
Operates on all tree wire and spacer cables |
| • |
Choice of handle styles |
| • |
Each tool built for a specific cable size |
| • |
Designed for HOT STICK operation |
| • |
Strips to any length in one continuous operation |
| • |
Strips at end or any point along cable length (mid-span) |
| • |
Please see Feature-Sheet for ordering information |
|
|
| |
|
|
| |
|
Length: 9.16 in (235.00 mm)
Weight: 1.9 lbs. (870.0 g)
| • |
For 15 to 35 KV cables, 0.50 inches (12.7 mm)
to 1.75 inches (44.5 mm) semi-con O.D |
| • |
Shaves “bonded” semi-con shield and insulation
material |
| • |
Shaves in a helical, spiral pattern leaving a radius cut
semi-con end |
| • |
Aluminum Oxide Kit (TK 1) can be used for further smoothing |
| • |
Precision adjustment of tool blade allows for accurate setup
for a range of cable and semi-con dimensions |
| • |
Contoured handle allows operator to advance the tool quickly
and evenly |
| • |
Guarded blade for added personnel protection |
| • |
Replacement blade: CB 40X |
|
|
| |
|
|
| |
|
|
